Enter your well test results
No bacteria test yet: the EPA advises testing a private well at least once a year for total coliform bacteria, nitrates, total dissolved solids and pH. Do that first, with a certified lab.
Your treatment train, in the order the water flows:
- 1Sediment filter
Most well systems start with one: it keeps sand and silt out of every valve and cartridge that follows.
- 2Iron, manganese and sulfur filter
Iron at 1.5 ppm is above the EPA secondary level of 0.3 mg/L. An oxidizing filter (air injection, greensand or catalytic carbon) takes these out before they foul a softener's resin or a UV sleeve.
Compare iron, manganese and sulfur filtersOur pick: SpringWell WS1Check price on Amazon
- 3Water softener
At 12 gpg your water is hard (Penn State puts hard at 7 to 10.5 gpg and very hard above that). A softener stops the scale; size it with the calculator.
Compare water softenersOur pick: EcoPure EP42Check price on Amazon
- 4UV disinfection
Until a lab test says the well is free of coliform bacteria, a UV unit at the end of the line is the usual safety net. Test first: it may not be needed.
Why does the order of the equipment matter?
Water check
Each step protects the next one. Sediment clogs every cartridge and valve, iron fouls softener resin, and a UV lamp only works on clear, low-iron water, so UV goes last and the sediment filter first.
Well water treatment is a train: the water goes through each unit in turn. Put a softener in front of an iron filter and the resin coats with iron; put a UV unit in front of the softener and scale clouds its quartz sleeve, so less light reaches the water. The finder follows the order most well treatment installers use, and it skips any step your numbers do not call for.
| Step | What it handles | When the finder adds it |
|---|---|---|
| 1. Sediment filter | sand, silt, grit | always on a well; needed if the water is cloudy |
| 2. Acid neutralizer | low pH that corrodes pipes | pH under 6.5 |
| 3. Iron, manganese and sulfur filter | stains, metallic taste, rotten egg smell | iron over 0.3 ppm, manganese over 0.05 ppm, or a sulfur smell |
| 4. Water softener | calcium and magnesium | hardness over 3.5 gpg (comfort) or over 7 gpg (recommended) |
| 5. UV disinfection | bacteria and viruses | coliform found, or no bacteria test yet |
| 6. Reverse osmosis at the tap | nitrate, arsenic, lead, PFAS | a lab result above the limit |
Which test results does the finder use?
Water check
Hardness, iron, manganese, pH, the smell, the look of the water and the coliform bacteria result. Those are the lines a basic well water test reports, and the ones that decide the equipment.
The EPA's private well guidance says to test at least once a year for total coliform bacteria, nitrates, total dissolved solids and pH, and more often after a flood or a change in taste, smell or color. Iron, manganese and hardness come from a fuller mineral panel. The finder compares iron, manganese and pH with the EPA secondary standards: 0.3 mg/L for iron, 0.05 mg/L for manganese and a pH of 6.5 to 8.5. Those levels are about taste, stains and corrosion, not health limits.
What does each step cost you in upkeep?
Water check
Sediment cartridges and UV lamps are replaced on a schedule, softeners need salt, and backwashing filters need a drain and some water. The guides behind each step give the figures from the makers' manuals.
A sediment cartridge is changed when the pressure drops; a UV lamp is usually replaced once a year, since its output fades even while it still glows. A calcite neutralizer needs its mineral topped up as it dissolves. Backwashing iron filters and softeners send water down a drain on a timer. The finder links each step to its guide when the guide is published: sediment filters, acid neutralizers, iron filters, softeners for well water, UV purifiers and under-sink reverse osmosis.
What are the limits of this finder?
Water check
It sorts common well problems into the usual order; it does not read a full lab report. Radon, uranium, high nitrate in a home with an infant, or a sudden change in the water need a water treatment professional and your health department.
The finder covers the problems most well owners meet. It does not size each unit for your flow rate in gallons per minute, which depends on your pump and your home. For the softener, use the water softener size calculator, and enter your iron there too. For everything about wells, start with the best well water filtration systems.
Sources
Our sources by topic
Public agencies and universities
- EPA, Private Drinking Water Wells: what to test and how often.
- EPA, Secondary Drinking Water Standards: iron, manganese, pH.
- Penn State Extension, Water Softening: hardness classes in grains per gallon.
Certification and standards bodies
- NSF, certified drinking water treatment units: NSF/ANSI 55 (UV) and 58 (reverse osmosis) listings.
